1402 Quick Cloning Kit
User Manual For Quick Cloning Kit
| Product Name |
Cat. No. |
Specifications |
Component |
| 1402 Quick Cloning Kit |
1402-1 |
50 rxns |
1 tube of 4X Cloning Enzyme Premix |
| 1402-5 |
250 rxns |
5 tubes of 4X Cloning Enzyme Premix |
Store at -20˚C
Overview
This product leverages a unique recombination mechanism that does not rely on ligase, enabling simple, rapid, and highly efficient targeted DNA cloning. The vector can be linearized by any method and then recombined with PCR fragments bearing 15–25 bp of homologous regions at both ends. The reaction is short in duration, with a recombination efficiency exceeding 95%, and it supports the efficient, seamless cloning of up to five DNA fragments.
Advantage
♦ Can be inserted at any position in any carrier
♦ Perform multi-fragment directional cloning in a single step—simple, accurate, and rapid—with reactions taking only 15 minutes and achieving an efficiency of up to 95%.
♦ Independent of ligase, PCR products require neither restriction digestion nor phosphorylation.
♦ Seamless integration, without introducing additional sequences
Cloning Experimental Procedure
I: Vector linearization, which can be achieved by enzymatic digestion or by PCR.
II: Preparation of the target fragment; the 5′ and 3′ terminal sequences of the PCR product are each completely identical to the corresponding terminal sequences of the linearized cloning vector.
III: Carrier—mix the insert fragment with the cloning reagent at a molar ratio of approximately 1:3, and incubate at 50°C for 15–30 minutes.
IV: Conversion of Reaction Products
Specific cloning experimental procedures
I: Vector Linearization
A linearized vector is a critical prerequisite for successful cloning and can be obtained by restriction digestion, with either blunt ends or sticky ends; double digestion is particularly effective in reducing background. Alternatively, it can be generated via PCR amplification, and the use of a high-fidelity DNA polymerase helps minimize unwanted mutations.
II: Primer Design
In addition to containing sequence-specific regions that are complementary to the target fragment, both the forward and reverse primers required for amplification must include 15–25 bp of overlapping sequences homologous to the ends of the vector. If restriction sites, adapter sequences, or tag sequences need to be introduced, they can be incorporated between these two regions. That is:
PCR Forward Primer = Vector forward overlap sequence (15–25 bp) + intermediate restriction site and other sequences + forward-specific sequence of the target fragment (20–25 bp)
PCR Reverse Primer = Vector reverse overlap sequence (15–25 bp) + intermediate restriction enzyme recognition site and other sequences + reverse-specific sequence of the target fragment (20–25 bp)
To clone multiple target fragments, the primer design principles between fragments are the same as described above.
III: Preparation of the Target Fragment
The target product should be amplified using a high-fidelity DNA polymerase. Since PCR primers are typically long, the annealing temperature can be determined based on the Tm of the specific region and the enzyme’s characteristics.
IV: Cloning Reaction System
| Recommended Amount |
|
| 4X Cloning Enzyme Premix |
5 μl |
| Linearized vector |
40~80 ng |
| Inserts |
Vector ng amount × 3 × fragment size (bp) / vector size (bp) = ng |
| Total Volume |
20 μl |
After gently mixing the reactants, incubate at 50°C for 15–30 minutes. Following completion of the reaction, the mixture can be used directly in subsequent transformations or stored at −20°C for later use.
Note:
1) When the recombination involves 2–3 fragments, the amounts of vector and each fragment should be approximately 0.02–0.5 pmol; when it involves 4–6 fragments, the amounts should be approximately 0.2–1 pmol. The optimal molar ratio of vector to the target fragment is 1:3.
2) When there are many recombined fragments, the reaction time may be appropriately extended to 1 hour.
V: Conversion
1. Place the competent cells on ice to thaw.
2. Add 20 μL of the recombinant reaction product intended for transformation, incubate on ice for 30 minutes, then subject to heat shock at 42°C for 60–90 seconds.
3. Continue to keep on ice for 2 minutes;
4. Add 500 μl of S.O.C or LB medium, and incubate on a shaker at 37°C for 1 hour;
5. After centrifuging the transformed bacterial suspension, discard the supernatant, gently resuspend the pellet, and evenly spread it onto LB plates containing the appropriate antibiotic.
6. Incubate at 37°C overnight in an inverted position.
Precautions
| Problem |
Probable cause |
Solution |
| Very few or no colonies after transformation. |
DNA concentration is too low. |
Use the recommended DNA amount. |
| The target fragment or vector contains contamination. |
Both the PCR products and the linearized vectors must be purified. |
|
| The efficiency of competent cells is too low. |
Use a potency greater than 1×10 8 Competent cells at a concentration of cfu/µg perform better. |
|
| Carrier linearization is incomplete. |
Gel extraction and recovery of the vector |
|
| Few positive clones were obtained, and most were empty vectors. |
Contaminated by a vector carrying the same resistance. |
PCR products may contain the template plasmid; gel extraction is recommended. |
| Flat resistance error |
Ensure that the plate is freshly prepared and contains the correct antibiotic. |
|
| The vector was incompletely digested. |
Extending the restriction digestion time can increase the degree of linearization and reduce background. |
Previous page
Previous page
Next page
Leave a message for inquiry
For more information about Zhongsheng All‑Peptide and its products, please contact us by message or phone. We will provide you with expert service and product support. Feel free to inquire:huang_qibei@peplib.com(Market Department Manager Huang)